{"product_id":"castair-replacement-industrial-v-type-belt-section-b-length-79","title":"Castair Replacement Industrial V-Type Belt Section B Length 79\"","description":"\u003cp\u003eThe Castair 3-B79 is a Section B industrial V-belt with a 79\" outside circumference, designed as a direct replacement drive belt for Castair belt-drive air compressors. If your compressor is slipping under load, squealing on startup, or the belt shows visible cracking or glazing, this is the correct replacement part. Section B is the standard profile for mid-range industrial compressors — wider and deeper than an A-section belt, handling the higher torque demands of piston pump drives without slipping. Contact us to confirm compatibility with your specific Castair compressor model.\u003c\/p\u003e\n\n\u003ch3\u003eBelt Specifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBelt Section:\u003c\/strong\u003e B — classical V-belt profile\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eTop Width:\u003c\/strong\u003e 17\/32 inch\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBelt Depth:\u003c\/strong\u003e 21\/32 inch\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eOutside Circumference:\u003c\/strong\u003e 79\"\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eConstruction:\u003c\/strong\u003e Classical wrapped construction with reinforcing cords and rubber compound body\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBelt Type:\u003c\/strong\u003e Non-cogged classical V-belt\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart Number:\u003c\/strong\u003e 3-B79\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePrice:\u003c\/strong\u003e $23.10\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompatibility and Fit\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePrimary Application:\u003c\/strong\u003e Castair belt-drive air compressors specifying a B79 or 3-B79 replacement belt\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSheave Type:\u003c\/strong\u003e Standard B-groove pulleys on motor and pump shafts\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLength Precision:\u003c\/strong\u003e Belt outside circumference determines the center distance between motor and pump shafts. A 1-inch difference in circumference translates to a real change in tension and center distance — order the exact length your compressor calls for, not the closest available.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCompatibility Note:\u003c\/strong\u003e Manufacturer-specific fitment data was not available at time of listing. Contact us to confirm compatibility with your specific Castair compressor model before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eInstallation Notes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eTension setting:\u003c\/strong\u003e Deflection at mid-span should be approximately 1\/2 inch per foot of free span under moderate thumb pressure. Consult your compressor manual for the exact figure for your model.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAlignment:\u003c\/strong\u003e Before tightening, lay a straightedge across both sheave faces to confirm motor and pump pulleys are in the same plane. Misalignment causes uneven sidewall wear and shortens belt life significantly.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBreak-in:\u003c\/strong\u003e After installing a new belt, run the compressor under load for 15-20 minutes, then shut down and recheck tension. New belts seat into the groove and lose some initial tension in the first operating hours.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eInstallation method:\u003c\/strong\u003e Loosen the motor mount adjustment to give slack, slip the belt onto both sheaves by hand, then move the motor to set tension. Do not pry the belt over the sheave flange — prying damages the internal cord structure and causes early failure.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eDual-belt configurations:\u003c\/strong\u003e If your compressor runs two belts side by side, replace both at the same time using matched belts from the same production batch. Running a new belt alongside a worn belt causes uneven load sharing — the new belt carries most of the torque and both belts wear out faster.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhen to Replace\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCracks:\u003c\/strong\u003e Cracks on the belt inner surface or sidewalls mean the rubber compound has hardened — the belt is near failure and should be replaced before it snaps during operation\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGlazing:\u003c\/strong\u003e A shiny, hard finish on the belt sidewalls means the belt has been slipping and heat-hardening the contact surface. A glazed belt will continue to slip regardless of tension adjustments.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFraying:\u003c\/strong\u003e Any fiber fraying on belt edges or the back surface indicates internal cord damage — replace immediately\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSlippage under load:\u003c\/strong\u003e If the motor runs at speed but the pump cannot keep up with demand, check belt tension first. Correct tension and the problem persists — the belt is worn out.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePersistent squealing:\u003c\/strong\u003e Brief squealing during a cold start in winter is normal. Squealing that continues under load means glazing or insufficient tension.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eInspection interval:\u003c\/strong\u003e Inspect every 300 operating hours. Typical service life is 2,000-4,000 hours depending on ambient temperature, duty cycle, and how often the compressor cycles on and off. High-cycle applications wear belts faster than continuous-run setups.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhy Buy From Air Compressor Factory Direct?\u003c\/h3\u003e\n\u003cp\u003eAir Compressor Factory Direct has been supplying shops and industrial facilities with compressor parts and diagnostic equipment since 2016. We stock the Castair V-belt lineup so you can order the exact replacement without substitution. Free shipping on every order. If you need help confirming the right belt for your specific Castair compressor — model number, configuration, or current belt markings — call our tech support team before you order. We will confirm the fit before you commit to the purchase.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eCall 866-217-0063 for quick answers and help!\u003c\/strong\u003e\u003c\/p\u003e","brand":"Cast Air","offers":[{"title":"Default Title","offer_id":53342506352853,"sku":"3-B79","price":42.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0622\/8466\/0949\/files\/beltb_834b6999-67cb-4dc5-beb0-454fff37b9eb.jpg?v=1772652507","url":"https:\/\/aircompressorfactorydirect.com\/products\/castair-replacement-industrial-v-type-belt-section-b-length-79","provider":"Air Compressor Factory Direct","version":"1.0","type":"link"}